PCIe Test Cards
High Quality PCIe Test Cards for Troubleshooting and Testing
Check the transmission speed, stability, and voltage of your PCIe slot with our new PCIe Test Card!
PCIe Test Cards are one of the fastest methods to diagnose, troubleshoot and load test your PC's PCI-e I/O functions.
When used with compatible PassMark testing software (see below) it is possible to:
These prices do not include shipping and do not include the BurnInTest Professional software. A MOLEX to 15-pin SATA adapter for voltage rail monitoring is included in the price.
An easy-to-use PCIe data loopback, throughput and voltage tester, the PassMark PCIe Test Card is an effective tool for verifying a PCIe slot is performing to specification.
Twenty-four on-board LEDs provide quick visual indications of I/O activity, data errors and power. Dedicated per-pin LEDs indicate which voltages are supplied to the slot (12V, 3.3V, 3.3Vaux) and from the PSU (12V and 5V), where 'Power Fail' LEDs paired with constant voltage sampling automatically reports whether any of the rails are outside of PCIe/ATX power spec.
When used with the Windows PCIeTest application, the user can run data loopback and benchmark tests in various test configurations. Benchmark tests use a bus-master DMA controller to maximise test transfer speeds between high-speed integrated LSRAM and system RAM up to a maximum theoretical speed of 5Gbps per lane. Note: After factoring in 8b/10b encoding, the raw maximum theoretical speed is 500 MBps and thus less for measurements of actual data payload throughput.
The PassMark PCIe Test Card also operates as a real-time voltage and temperature monitoring device, allowing the user to view PCIe and power supply voltage rails and temperature measurements over time.
Each Test Card carries a unique serial number that can be used to distinguish between multiple connected devices. No additional connections or power supply is required beyond the PCIe slot, (except when monitoring PSU 12V and 5V rails). Extra-thick 100 µinch hard gold plating on 150 µinch nickel fingers ensure greater durability and rated insertion cycling than typical PCIe cards.
|PCIe Standard:||Gen2 and Gen1
(also compatible with Gen3 up to Gen2 speeds)
|Plug and play:||Compliant|
|Physical connector:||x1 and x4 PCIe edge connectors (card can be flipped)
|PCIe Transfer modes:||DMA - Direct memory access|
|Device memory:||96KB of high speed integrated LSRAM|
|ADC Sample Rate:||1MHz per channel, dual channel (up to 2 million voltage measurements per second)|
|No. of Channels||2 (up to 2 channels can be measured simultaneously)|
|No. of Measurement Sources:||6 (Voltage rails & Temperature)|
|Voltage Rails Monitored||12V PCIe, 3.3V PCIe, 3.3Vaux, 12V PSU, 5V PSU|
|ADC Resolution:||12 bits|
|Size:||85mm x 45mm x 12mm (3.4 x 1.8 x 0.5 inches)|
Green LEDs for each 12V pin (5)
Red LED = 12V out of spec'd range
Green LEDs for each 3.3V pin (3)
Red LED = 3.3V out of spec'd range
Green LED for 3.3V aux rail
Green LED for 12V PSU rail (from Molex/SATA connector)
Red LED = 12V out of spec'd range
Green LED for 5V PSU rail (from Molex/SATA connector)
Red LED = 5V out of spec'd range
Yellow LED = TX Activity
Green LED = RX Activity
Red LED = I/O Error
Orange LED = Sleep
Green LED = PCIe Gen2/3
Yellow LED = Misc
Green LED = Loopback Mode
Yellow LED = Benchmark Mode
Orange LED = Oscilloscope Mode
|EMC standards:||AS/NZS 3548:1995, EC.|
|Storage Temperature:||-30 ºC to 80 ºC|
|Usage Temperature:||0 ºC to 70ºC|
|Max speed:||5 Gbits/sec per lane|
|RoHS (Lead free) :||Yes|
|C-Tick Compliance Tested:||Yes|
The specifications above are for the PassMark PCIe Test Card.
- 4-pin female MOLEX to 15-pin male SATA adapter for connecting the on-board MOLEX to PSU SATA outputs.
- PCIeTest software and Windows Drivers
- PCIe Test Card user guide and instructions
Windows 32bit: Windows 7, 8 & 10 are supported.
Windows 64bit: Server 2012, Windows 7, 8 and 10 are supported.
Linux: Compatible with BurnInTest for Linux V3.4 and above
Windows XP, Vista and Mac are not supported.
In order to use the PCIe Test Card you also need one of the following 3 software applications.
A) BurnInTest Professional v8.1 or higher
B) BurnInTest for Linux V3.4 or higher
C) The free stand alone PCIeTest software for Windows. Download here
PCIe slots of all sizes are supported, however the test card can only test up to the first four lanes of any slot.
Please contact for more ordering details.